Quick Answer
Standard back-to-back aircond installation in Kuala Lumpur starts at RM199 for 1.0 HP, RM240 for 1.5 HP, RM290 for 2.0 HP, and RM350 for 2.5 HP+. This base price includes up to 6 feet of insulated copper piping, 10 feet of PVC drain pipe, outdoor brackets, and full vacuuming.
Back-to-Back vs Extended Copper & PVC Trunking Runs
The biggest cost variable in any KL installation is the distance between your indoor wall and the outdoor condenser ledge. In a back-to-back setup, the indoor unit mounts on an exterior wall with the compressor sitting directly behind it, needing under 6 feet of pipe.
In many KL condominiums, however, all outdoor units sit on a shared balcony yard ledge 12 to 25 feet away. If concealed pipes were not pre-laid by the developer, extra insulated copper pipe and neat boxed PVC trunking are measured transparently per foot.
Choosing the Right Horsepower (HP) for Malaysian Rooms
Buying an undersized 1.0 HP unit for a large sunny room forces the compressor to run at 100% load nonstop, burning more electricity while never feeling crisp. Use this reliable Klang Valley sizing guide: Room Area (sq ft) × 65 BTU (add 15% for west-facing afternoon sun).
- Up to 140 sq ft (medium bedroom / study): 1.0 HP (~9,000 - 9,500 BTU).
- 140 to 230 sq ft (master bedroom): 1.5 HP (~12,000 - 13,000 BTU).
- 230 to 360 sq ft (condo living-dining hall): 2.0 HP (~18,000 BTU).
- 360 to 500 sq ft (open-plan terrace living hall): 2.5 HP - 3.0 HP (~22,000 - 28,000 BTU).
3 Non-Negotiable Quality Checks During Installation
Whether you book us or any installer, insist on these three quality steps:
- Full Vacuum Pump Evacuation (15-20 mins): Removes air and moisture from copper lines before releasing high-pressure R32/R410A gas.
- Pour-Test on Condensate Drain: Pouring water directly into the indoor tray to confirm brisk gravity drainage before snapping the cover shut.
- Proper Copper Wall Gauge: Using minimum 0.61mm - 0.71mm insulated copper tubing rated for inverter pressures.
KL Aircond Installation Rates & Optional Add-on Guide (2026)
| Capacity / Work Item | Rate (RM) | Included Scope / Notes |
|---|---|---|
| 1.0 HP Standard Back-to-Back Install | RM199 | 6 ft copper pipe, 10 ft PVC drain, bracket & vacuum |
| 1.5 HP Standard Back-to-Back Install | RM240 | 6 ft copper pipe, 10 ft PVC drain, bracket & vacuum |
| 2.0 HP Standard Back-to-Back Install | RM290 | 6 ft larger-bore copper, heavy bracket & vacuum |
| 2.5 HP - 3.0 HP Standard Install | RM350 | 6 ft heavy-gauge copper, heavy bracket & vacuum |
| Extra Copper Piping (>6 ft) | RM22 - RM32 / ft | Sized by HP, includes insulation & interconnect wire |
| Boxed PVC Trunking Casing | RM15 / ft | Conceals indoor surface pipe runs neatly |
| New 20A Power Point & Switch | RM120 - RM180 | Surface conduit wiring when no adjacent point exists |
| Dismantle Old Unit (with Pump-down) | RM80 / unit | Safely locks existing refrigerant before removal |
Estimated Total Cost & Getting a Fast Photo Quote
WhatsApp us 2 quick photos of your indoor wall and outdoor compressor spot for a firm quote before we head over.
- •1.0 HP bedroom back-to-back (existing power point): RM199 all-in.
- •Condo hookup onto existing concealed piping (1.0 - 1.5 HP, with vacuum): RM199 - RM240.
- •1.5 HP with a 15-foot trunked indoor run: typically RM450 - RM540 complete.
Book a Fast Service Slot
Select service, area, and date above to enable the booking button.